CP80 PRINTER DRIVER DOWNLOAD

Remove the card hopper. Request a Quote There are three ways to get more information on this product and to receive a custom quote: Press in on the two retaining tabs and rotate the motor counterclockwise to remove it. Each routine can be run individually or as a procedure of successive routines. These may or may not be used by various device manufacturers. Slide the transport chassis back, and simultaneously pull forward on the card hopper.

Uploader: Zular
Date Added: 27 March 2004
File Size: 29.79 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 18782
Price: Free* [*Free Regsitration Required]

Remove the two screws that secure the motor to the transport chassis, and remove the motor. Wipe the exterior of the printer with a cloth dampened with a non-abrasive, general purpose cleaning solution.

Main Enclosure page Duplex Home Offset Duplex Home Offset This parameter controls where the duplex flipper stops when in the home position. Fluorescent text can be seen only under UV light, which makes it easy to validate the authenticity of the ID card and severely hinders any attempt at forgery.

Handoff offset should be 77 units larger than the Home offset. This is called inductive coupling, and is similar to the function of a transformer.

J. O’Brien Company

This releases the small locking nibs on the ends of the ribbon guide see inset photo below. Page Option Purpose Printer Motor Tests This option allows you to operate each of the motors in the printer for a specified duration as described in Testing Motors.

Page Remove the cpp80 screws that secure the pick motor to the transport chassis, and remove the motor. Page The plastic gears are not retained on their shafts.

  CALDIGIT EXPRESSCARD 34 USB3.0 DRIVER

Gently press the side of a screwdriver against the tip of the sensor removal access slot shown below and push it out of the chassis. Rear Drive Roller If present, partially remove the smart card contact carrier: Page 25 The duplex c;80 sensor detects the card and determines the position within the flipper. Error Symptom Comments Code MS A card was lost when The card was never detected by either the attempting to read or write magnetic stripe or card input sensors.

Remove both halves of the Main Enclosure page Push the cover toward the swingarm latch, and then rotate it upward to release the forward retaining tab. Be careful not to lose the springs.

Security Card Printers : Datacard CP80 Plus

Move the back edge of the guard past the sensor pocket. When the two halves are separated, all of the components are free to fall loose. Slide the transport chassis back, and simultaneously pull forward on the card hopper.

Disconnect the duplex interface cable from the interface board.

Datacard CP80 ID Card & Driver License Printer

The MAC Address is a unique identifier for the physical ccp80. Transport Assembly This is a general procedure for removing the transport assembly from the printer. Mechanical Inspection Wipe the exterior of the printer with a cloth dampened with a non-abrasive, general purpose cleaning solution.

Reader to Card Communication The reader communicates with the card by sending an amplitude modulated signal at Select this option and click Query to display the type of ribbon detected by the printer in the display window Laminate information This option is available only for the CP80 and CP80 Plus printers.

  COMPAQ 6910P ACPI SMCF010 DRIVER DOWNLOAD

Disconnect the foil advance motor connector from the laminator control board. Close and lock the swingarm, and turn the printer upside down. Printer Components Sensors All of the optical sensors in the CP80 and CP80 Plus printers are of the open collector type, and are configured to be active-low with a pull-up resistor on the output.

General Notes General Notes This document is organized xp80 for the customer engineer who is encountering an CP80 or CP80 Plus printer for the first time, and begins with installing the diagnostic software, navigating and using the software, and concludes with specific adjustment procedures for the printer. The Magnetic Write Head contains a small coil of wire wrapped around a semicircular iron core. Enter key to move to the next field.

Output Hopper Removal Procedure Turn off the printer and unplug the printee cord. Working With Scripts The script can then be loaded into another printer for batch processing a series of printers.